Tag Archives: fiber transceiver type

How to Choose the Right Type of Optical Transceiver

Choosing the right optical transceiver is not easy. You can approach the selection process by reviewing the device as a single entity or you can explore the fiber cable separately. Either way, you need to be aware of what’s needed for your application to work optimally. If you know what you need to edge out the competition, you’ll be in a better position when you’re speaking with representatives about the fiber optic cable. Here’s what you should consider:

Which Fiber Mode That’s Required
There are two basic types of fiber: multimode fiber and single-mode fiber. Multimode fiber will allow each signal to travel on more than one pathway at one time, which is best designed for short transmission distances, and is suited for use in LAN systems and video surveillance. Single-mode fiber is best designed for longer transmission distances, which is used in applications that need bandwidth that will travel over long distances.

Determine if You’ll Need Full-Duplex or Half-Duplex
Some chips will only use full-duplex configuration. Selecting switches, HUBs, or transceivers with half-duplex mode may cause loss and conflict. Only choose full-duplex unless you think that your application can support half-duplex. Nowadays, Ethernet interfaces on the switch operate at 10, 100, or 1000 Mbps, or 10,000 Mbps and in either full- or half-duplex mode.

Consider Whether You’ll Need a Safety Device to Prevent Packet Loss
Some vendors may just need to reduce costs and loss. Thus, they have to choose an optical transceiver with maximum safety features and loss prevention.

Consider Whether the Transceivers Have Temperature Adaptability
Optical transceivers shouldn’t run hot. Optical transceivers may fail prematurely at high temperatures. That is why it’s important to know how well an optical transceivers can adapt to heat if it will be in high temperatures.

Determine if You’ll Need Copper or Optical Fiber
Take an example of Gigabit Ethernet SFP module, 1000BASE-T (e.g. GLC-T) SFP module operates on standard Category 5 wiring and has a RJ-45 connector. 1000BASE-SX SFP transceiver operates on ordinary multi-mode fiber optic link spans of up to 550 m in length. 1000BASE-LX/LH SFP operates on single-mode fiber (SMF) for a maximum length of 10km. 1000BASE-ZX SFP using an extended wavelength operates on single-mode optical fiber for up to 100km.

Consider the Construction of the Fiber You’ll Need
There are some basic types of internal construction, but you have to choose the one that will work best for your application. One of the most popular types is the distribution or tight pack. The second type of construction is the breakout or fanout design. This design gives each buffered fiber its own individual jacket and is a more durable design.

optical transceiver typeThe zip cord or assembly is another type of internal construction that is offered to the designers. This is one of the preferred internal construction options. In this construction, one or two buffered fibers in individual jackets should be considered. Single fiber cable is recommended for patching.

The last factor you should consider is the level of flame resistance. Remember that there are three different grades available: general, special, and high. The level of flame resistance can be measured through a variety of tests including those determining smoke density values and flame propagation.

Choosing the Right Fiber Transceiver Type is Not Easy
Choosing the right fiber transceiver type is not easy. There are lots of elements to be considered. These are typically considered on a case-by-case basis. Consider all of the factors mentioned such as the internal construction, fiber mode, fiber cable jackets, and the level of flame resistance.

OEM Optical Transceiver Solution
FS.COM is a professional OEM manufacturer and supplier of optical networking solutions, which can supply 100% compatible Cisco SFP and SFP+ transceivers, such as GLC-SX-MM, GLC-SX-MMD, GLC-T, GLC-LH-SMD and GLC-FE-100LX, etc. According to your requirements, FS.COM welcomes any inquiry for customized optical transceiver type.

Related Articles: How to Select the Right Fiber Patch Cable for 40G QSFP+ Transceiver?

                              SFP Module: What’s It and How to Choose It?

What Is An Optical Module?